濟南奧迪汽車在使用過程中，難免因碰撞、剮蹭或意外擠壓出現車身凹陷，不僅影響外觀，還可能因凹陷處漆面開裂導致銹蝕。處理時需根據凹陷大小、位置、漆面狀態及車型結構（如奧迪車身的鋁合金部件比例）選擇合適方法，兼顧修復效果與原廠漆面保護，確保恢復車輛原貌的同時不影響車身強度。

　　During the use of Audi cars in Jinan, it is inevitable that the body may be dented due to collisions, scratches, or accidental compression, which not only affects the appearance but may also cause corrosion due to cracks in the paint surface at the dented area. When handling, appropriate methods should be selected based on the size, location, paint condition, and vehicle structure (such as the proportion of aluminum alloy components in Audi bodies) of the dents, taking into account both repair effectiveness and original paint protection, to ensure that the vehicle's original appearance is restored without affecting its strength.

　　輕微凹陷（深度≤5mm，面積≤10cm）且漆面完好時，優先采用無損凹陷修復技術，適合濟南市區常見的小磕碰（如被石子撞擊、輕微追尾）。該技術通過特制工具（如不同尺寸的撬棍、吸杯）從車身內部或外部發力，利用金屬的延展性將凹陷逐步頂起，過程中不損傷原廠漆面（奧迪原廠漆面為多層復合涂層，修復后光澤度需保持 90% 以上）。操作時需先清潔凹陷區域，用強光燈照射確定凹陷中心點與邊緣，再用撬棍從車門內側空腔、翼子板縫隙等部位伸入，根據凹陷弧度調整發力角度（每次調整不超過 5°），避免因用力過猛導致漆面拉伸開裂。對于弧形表面（如奧迪引擎蓋、后備箱蓋），需配合吸盤輔助固定，防止修復過程中出現新的變形，這類修復通常 1-3 小時可完成，且能保留原廠漆的防腐性能，尤其適合白色、銀色等易產生色差的車型。

　　When there is a slight dent (depth ≤ 5mm, area ≤ 10cm) and the paint surface is intact, non-destructive dent repair technology is preferred, which is suitable for common small bumps in Jinan city (such as being hit by stones or minor rear end collisions). This technology uses specially designed tools (such as pry bars of different sizes, suction cups) to apply force from the inside or outside of the vehicle, gradually lifting the depression using the ductility of the metal, without damaging the original paint surface (Audi's original paint surface is a multi-layer composite coating, and the glossiness needs to be maintained at over 90% after repair). When operating, it is necessary to clean the depressed area first, use a strong light to determine the center point and edge of the depression, and then use a pry bar to insert from the inner cavity of the car door, the gap between the fenders, and other parts. Adjust the force angle according to the curvature of the depression (no more than 5 ° each time) to avoid the paint surface stretching and cracking due to excessive force. For curved surfaces such as Audi engine hood and trunk lid, suction cups should be used to assist in fixing to prevent new deformations during the repair process. This type of repair can usually be completed in 1-3 hours and can retain the anti-corrosion performance of the original factory paint, especially suitable for white, silver and other car models that are prone to color differences.

　　中度凹陷（深度 5-15mm，面積 10-50cm）若漆面未破損，可采用加熱輔助修復，適合濟南夏季因高溫暴曬后車身輕微變形的修復。先用紅外烤燈（溫度控制在 60-80℃）加熱凹陷區域（奧迪鋁合金部件需降低溫度至 50℃以下，避免金屬變軟），使金屬延展性增強，再結合無損修復工具頂推凹陷。加熱時需保持烤燈與車身距離≥30cm，避免局部過熱導致漆面變色（黑色漆面耐溫性略高，白色漆面需格外注意）。對于車門、葉子板等雙層結構的凹陷，需拆開內飾板或內襯，確保工具能直接接觸凹陷背面，修復后檢查漆面是否有細微裂紋（可用漆膜儀檢測厚度變化，偏差應≤5μm），必要時涂抹專用釉料增強漆面附著力，防止后期出現脫漆。

　　Moderate depression (depth 5-15mm, area 10-50cm) can be repaired with heating assistance if the paint surface is not damaged. It is suitable for repairing slight deformation of the car body in Jinan during summer due to high temperature exposure. First, use an infrared baking lamp (temperature controlled at 60-80 ℃) to heat the recessed area (Audi aluminum alloy parts need to lower the temperature to below 50 ℃ to avoid metal softening), to enhance the metal ductility, and then use non-destructive repair tools to push the recessed area. When heating, it is necessary to maintain a distance of ≥ 30cm between the baking lamp and the vehicle body to avoid local overheating that may cause discoloration of the paint surface (black paint surface has slightly higher temperature resistance, white paint surface needs special attention). For dents in double-layer structures such as car doors and leaf panels, it is necessary to remove the interior panel or lining to ensure that the tool can directly contact the back of the dent. After repair, check the paint surface for minor cracks (thickness changes can be detected using a paint film gauge, with a deviation of ≤ 5 μ m). If necessary, apply special glaze to enhance the adhesion of the paint surface and prevent paint peeling in the later stage.

　　深度凹陷（深度＞15mm）或漆面已破損（如劃痕、開裂）時，需采用傳統鈑金修復，適合嚴重碰撞后的修復。先評估凹陷處是否存在金屬折痕（折痕會導致金屬內部應力集中，直接影響修復效果），若有折痕需先用專用工具進行應力釋放（通過反復輕微敲擊消除金屬記憶）。修復時用鈑金錘配合墊鐵從內側敲擊，墊鐵需與車身曲面貼合（誤差≤1mm），避免敲擊時產生新的凹點，奧迪的高強度鋼部件（如 A 柱、B 柱）需控制敲擊力度，防止金屬疲勞。漆面破損處需先清除破損漆層（用 800 目砂紙打磨至露出金屬），涂抹防銹底漆（奧迪推薦鋅含量≥95% 的環氧底漆），待底漆干燥后（25℃環境下約 30 分鐘）再進行鈑金作業，避免金屬裸露在濟南潮濕環境中生銹。

　　When there is a deep depression (depth>15mm) or the paint surface is damaged (such as scratches or cracks), traditional sheet metal repair is required, which is suitable for repairing after severe collisions. Firstly, evaluate whether there are metal creases in the concave area (creases can cause stress concentration inside the metal, directly affecting the repair effect). If there are creases, special tools should be used to release the stress first (by repeatedly tapping lightly to eliminate metal memory). When repairing, use a sheet metal hammer in conjunction with a shim to strike from the inside. The shim should be in contact with the curved surface of the vehicle (with an error of ≤ 1mm) to avoid creating new concave points during striking. Audi's high-strength steel components (such as A-pillars and B-pillars) need to control the striking force to prevent metal fatigue. The damaged paint layer should be removed first (polished with 800 grit sandpaper until the metal is exposed), and anti rust primer (Audi recommends epoxy primer with zinc content ≥ 95%) should be applied. After the primer dries (about 30 minutes at 25 ℃), sheet metal work can be carried out to avoid metal exposure and rusting in the humid environment of Jinan.

　　特殊部位凹陷（如棱角處、車身腰線、鋁合金部件）處理需更精細，因奧迪部分車型采用全鋁車身（如 A8L、Q7 的部分版本），鋁合金延展性與鋼材不同（鋁合金拉伸后無法完全恢復），修復時需使用專用鋁制工具，發力強度比鋼材低 30%，且避免反復調整。車門邊緣、引擎蓋邊角等棱角凹陷，需采用 “漸進式” 修復，每次頂推幅度不超過 1mm，配合塑料撬片保護漆面，防止邊角處漆面因受力集中而剝落。對于涉及車身結構的凹陷（如后備箱圍板、縱梁附近），修復后需用專業儀器檢測車身平整度（誤差應≤2mm/m），確保不影響車輛碰撞安全性，濟南部分維修機構配備車身校正儀，可通過 3D 掃描實時監測修復過程，保證數據符合原廠標準。

　　Special areas such as corners, body waistline, and aluminum alloy components require more precise treatment, as some Audi models use all aluminum bodies (such as some versions of A8L and Q7), and the ductility of aluminum alloy is different from that of steel (aluminum alloy cannot be fully restored after stretching). When repairing, special aluminum tools are required, with a 30% lower strength than steel and avoiding repeated adjustments. The edges of the car doors, engine hood corners, and other sharp depressions need to be repaired using a "progressive" approach, with each push not exceeding 1mm. Plastic pry plates should be used to protect the paint surface and prevent peeling of the paint surface at the corners due to concentrated force. For dents involving the body structure (such as the trunk panel and near the longitudinal beam), professional instruments are needed to check the flatness of the body after repair (with an error of ≤ 2mm/m) to ensure that it does not affect the safety of vehicle collisions. Some repair institutions in Jinan are equipped with body correction instruments, which can monitor the repair process in real time through 3D scanning to ensure that the data meets the original factory standards.

　　修復后的漆面處理是保障長期效果的關鍵，尤其濟南多雨、冬季有融雪劑的環境需加強防護。無損修復后若漆面有細微劃痕，可進行鏡面拋光（用 3000 目砂紙輕磨后，配合氧化鈰拋光劑），使漆面光澤度恢復至原廠水平。鈑金修復后的漆面需重新噴涂，采用 “多層修復法”：先噴中涂底漆（厚度 30-50μm）增強附著力，再噴色漆（與原廠色號匹配，奧迪需使用專用色母），最后噴清漆（厚度 40-60μm）提升光澤度與耐磨性，噴涂后需在恒溫烤房（60℃）烘烤 1 小時，確保漆面固化完全。修復后 3 個月內避免高壓水槍直接沖洗修復區域，冬季洗車后及時擦干，防止融雪劑殘留侵蝕漆面，延長修復部位的使用壽命。

　　The treatment of the repaired paint surface is the key to ensuring long-term effectiveness, especially in the rainy and winter environment of Jinan where there is a need to strengthen protection. If there are minor scratches on the paint surface after non-destructive repair, mirror polishing (lightly sanded with 3000 grit sandpaper and combined with cerium oxide polishing agent) can be performed to restore the glossiness of the paint surface to the original factory level. After sheet metal repair, the paint surface needs to be repainted using the "multi-layer repair method": first, spray the intermediate primer (thickness 30-50 μ m) to enhance adhesion, then spray the colored paint (matching the original color number, Audi needs to use a special color masterbatch), and finally spray the clear paint (thickness 40-60 μ m) to improve glossiness and wear resistance. After spraying, it needs to be baked in a constant temperature oven (60 ℃) for 1 hour to ensure complete curing of the paint surface. Within 3 months after repair, avoid direct flushing of the repair area with high-pressure water guns. After washing the car in winter, dry it promptly to prevent residual snow melting agents from eroding the paint surface and extend the service life of the repair area.

　　本文由濟南奧迪汽車維修友情奉獻.更多有關的知識請點擊:http://www.godfife.com.cn我們將會對您提出的疑問進行詳細的解答，歡迎您登錄網站留言.

　　This article is a friendly contribution from Volvo Car Repair in Jinan For more information, please click: http://www.godfife.com.cn We will provide detailed answers to your questions. You are welcome to log in to our website and leave a message